doc.# dsfp-lp0701 b071513 lp0701 absolute maximum ratings parameter value drain-to-source voltage bv dss drain-to-gate voltage bv dgs gate-to-source voltage 10v operating and storage temperature -55c to +150c absolute maximum ratings are those values beyond which damage to the device may occur. functional operation under these conditions is not implied. continuous operation of the device at the absolute rating level may affect device reliability. all voltages are referenced to device ground. pin confguration to-92 8-lead soic d d d d g s nc nc features ? ultra-low threshold ? high input impedance ? low input capacitance ? fast switching speeds ? low on-resistance ? freedom from secondary breakdown ? low input and output leakage applications ? logic level interfaces ? solid state relays ? battery operated systems ? photo voltaic drives ? analog switches ? general purpose line drivers p-channel enhancement-mode lateral mosfet general description these enhancement-mode (normally-off) transistors utilize a lateral mos structure and supertexs well-proven silicon- gate manufacturing process. this combination produces devices with the power handling capabilities of bipolar transistors and with the high input impedance and negative temperature coeffcient inherent in mos devices. characteristic of all mos structures, these devices are free from thermal runaway and thermally induced secondary breakdown. the low threshold voltage and low on-resistance characteristics are ideally suited for hand held, battery operated applications. product marking 8-lead soic yy = year sealed ww = week sealed = ?green? packaging si lp 0701 yyww to-92 yy = year sealed ww = week sealed l = lot number = ?green? packaging yyww p0701 llll package may or may not include the following marks: si or package may or may not include the following marks: si or gate source drain product summary bv dss /bv dgs r ds(on) v gs(th) i d(on) -16.5v 3.0k -1.0v (max) 3.0ma (min) -g denotes a lead (pb)-free / rohs compliant package refer to p0xx tape & reel specs for p002, p003, p005, p013, and p014 to-92 taping specifcations and winding styles part number package options packing lp0701lg-g 8-lead soic 2500/reel lp0701n3-g to-92 1000/bag lp0701n3-g p002 to-92 2000/reel lp0701n3-g p003 to-92 2000/reel lp0701n3-g p005 to-92 2000/reel lp0701n3-g p013 to-92 2000/reel lp0701n3-g p014 to-92 2000/reel ordering information supertex inc. supertex inc. www .supertex.com
2 doc.# dsfp-lp0701 b071513 lp0701 thermal characteristics package i d (continuous ) ? (ma) i d (pulsed) ? (a) power dissipation @t c = 25 o c (w) ja ( o c/w) i dr (ma) i drm ? (a) 8-lead soic -700 -1.25 1.5 ? 101 ? -700 -1.25 to-92 -500 -1.25 1.0 132 -500 -1.25 notes: ? i d (continuous) is limited by max rated t j . ? mounted on fr4 board, 25mm x 25mm x 1.57mm sym parameter min typ max units conditions bv dss drain-to-source breakdown voltage -16.5 - - v v gs = 0v, i d = -1.0ma v gs gate threshold voltage -0.5 -0.7 -1.0 v v gs = v ds , i d = -1.0ma v gs(th) change in v gs(th) with temperature - - -4.0 mv/ o c v gs = v ds , i d = -1.0ma i gss gate body leakage - - -100 na v gs = 10v, v ds = 0v i dss zero gate voltage drain current - - -100 na v ds = -15v, v gs = 0v - - -1.0 ma v ds = 0.8 max rating, v gs = 0v, t a = 125 o c i d(on) on-state drain current - -0.4 - a v gs = v ds = -2.0v -0.6 -1.0 - v gs = v ds = -3.0v -1.25 -2.30 - v gs = v ds = -5.0v r ds(on) static drain-to-source on-state resistance - 2.0 4.0 v gs = -2.0v, i d = -50ma - 1.7 2.0 v gs = -3.0v, i d = -150ma - 1.3 1.5 v gs = -5.0v, i d = -300ma r ds(on) change in r ds(on) with temperature - - 0.75 %/ o c v gs = -5.0v, i d = -300ma g fs forward transconductance 500 700 - mmho v gs = -15v, i d = -1.0a c iss input capacitance - 120 250 pf v gs = 0v, v ds = -15v, f = 1.0mhz c oss common source output capacitance - 100 125 c rss reverse transfer capacitance - 40 60 t d(on) turn-on delay time - - 20 ns v dd = -15v, i d = -1.25a, r gen = 25? t r rise time - - 20 t d(off) turn-off delay time - - 30 t f fall time - - 30 v sd diode forward voltage drop - -1.2 -1.5 v v gs = 0v, i sd = -500ma notes: 1. all d.c. parameters 100% tested at 25 o c unless otherwise stated. (pulse test: 300s pulse, 2% duty cycle.) 2. all a.c. parameters sample tested. electrical characteristics (t a = 25c unless otherwise specifed) 90% 10% 90% 90% 10% 10% pulse generator vdd r l output d.u.t. t (on) t d(on) t (off) t d(off) t f t r input r gen input output 0v vdd 0v -10v switching waveforms and test circuit supertex inc. www .supertex.com
3 doc.# dsfp-lp0701 b071513 lp0701 typical performance curves saturation characteristics 0- 1- 2- 3- 5 -4 maximum rated safe operating area -0.1 -100 -10 -1.0 -0.1 -1.0 -10 -0.01 thermal response characteristic s thermal resistance (normalized) 1.0 0.8 0.6 0.4 0.2 0.00 11 0 0.01 0.1 1.0 transconductance vs. drain current 1.0 0.8 0.6 0.4 0.2 0 0 -2.0 -1.0 power dissipation vs. case t emperatur e 01 50 100 50 2 1 0 125 75 25 t a = -55 o c to-92 (dc) so-8 (dc) to-92 to-92/so-8 (pulsed ) -4v -3v -2v -1v -2.5 -2.0 -1.5 -1.0 -0.5 0 0 output characteristics -2.5 -2.0 -1.5 -1.0 -0.5 0 0- 4- 8- 12 -16 v gs = -5.0v -4v -3v -2v -1v i d (amperes) v ds (volts) g fs (seimens) p d (watts) t c ( o c) i d (amperes) v ds (volts) t p (seconds ) to-92 t c = 25v p d = 1.0w so-8 i d (amperes) v ds (volts) i d (amperes) v gs = -5.0v v ds = -15v t a = 25 o c t a = 125 o c t c = 25 o c supertex inc. www .supertex.com
4 doc.# dsfp-lp0701 b071513 lp0701 typical performance curves (cont.) gate drive dynamic characteristics q g (nanocoulombs ) v gs(th) (normalized ) r ds(on) (normalized ) v (th) and r ds v ariation with te mperature on-resistance vs. drain current bv dss v ariation with te mperature bv dss (normalized) transfer characteristics capacitance vs. drain-to-source v oltage 200 c (picofarads) 0- 5 -10 -15 100 0- 1- 2- 3- 4- 5 -2 -1 -500 50 1001 50 1.1 10 8 6 4 2 0 0 -3 1.4 1.2 1.0 0.8 0.6 0.4 1.6 1.4 1.2 1.0 0.8 0.6 -10 -8 -6 -4 -2 0 012345 -50 05 0 100 150 238pf f = 1.0mhz -1 -2 -20v 0 v ds = -15v 0.9 1.0 c iss = 115pf r ds(on) @ -5v, -300ma 0 t a = 125 o c v gs = -2.0v i d (amperes ) t j ( o c) r dss(on) (ohms) i d (amperes ) v gs (volts) v ds = -10v v ds (volts) v gs (volts) c iss c oss c rss t j ( o c) v gs = -3.0v v gs = -5.0v t a = 25 o c t a = -5 5 o c v (th) @ -1.0ma supertex inc. www .supertex.com
5 doc.# dsfp-lp0701 b071513 lp0701 1 8 seating plane gauge plane l l1 l2 e e1 d e b a a2 a1 seating plane a a t op vi ew side v iew vi ew b v iew b 1 note 1 (index area d/2 x e1/2) vi ew a-a h h note 1 symbol a a1 a2 b d e e1 e h l l1 l2 1 dimension (mm) min 1.35* 0.10 1.25 0.31 4.80* 5.80* 3.80* 1.27 bsc 0.25 0.40 1.04 ref 0.25 bsc 0 o 5 o nom - - - - 4.90 6.00 3.90 - - - - max 1.75 0.25 1.65* 0.51 5.00* 6.20* 4.00* 0.50 1.27 8 o 15 o jedec registration ms-012, variation aa, issue e, sept. 2005. * this dimension is not specifed in the jedec drawing. drawings are not to scale. supertex doc. #: dspd-8solgtg, version i041309. note: 1. this chamfer feature is optional. a pin 1 identifer must be located in the index area indicated. the pin 1 identifer can be: a molded mark/identifer; an embedded metal marker; or a printed indicator. 8-lead soic (narrow body) package outline (lg) supertex inc. www .supertex.com
6 lp0701 (the package drawing(s) in this data sheet may not refect the most current specifcations. for the latest package outline information go to http://www.supertex.com/packaging.html .) doc.# dsfp-lp0701 b071513 3-lead to-92 package outline (n3) symbol a b c d e e1 e e1 l dimensions (inches) min .170 .014 ? .014 ? .175 .125 .080 .095 .045 .500 nom - - - - - - - - - max .210 .022 ? .022 ? .205 .165 .105 .105 .055 .610* jedec registration to-92. * this dimension is not specifed in the jedec drawing. ? this dimension differs from the jedec drawing. drawings not to scale. supertex doc.#: dspd-3to92n3, version e041009. seating plane 1 2 3 front v iew side v iew bottom v iew e1 e d e1 l e c 1 2 3 b a supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such appl ications unless it receives an adequate ?product liability indemnification insurance agreement.? supertex inc. does not assume responsibility for use of devices described, and limits its liabilit y to the replacement of the devices determined defective due to workmanship. no responsibility is assumed for possible omissions and inaccuracies. circuitry and specifications are subject to change without notice. for the latest product specifications refer to the supertex inc. (website: http//www .supertex.com) ?2013 supertex inc. all rights reserved. unauthorized use or reproduction is prohibited. supertex inc. 1235 bordeaux drive, sunnyvale, ca 94089 t el: 408-222-8888 www .supertex.com
|
